This chapter describes Dials messages. For information on message content and how to use the message, refer to the Introduction.
| DIAL.001 |
Level: C-TRACE
Short Syntax: DIAL.001 CML X31 DSIO: pkt xmted nt network ID
Long Syntax: DIAL.001 CML X31 DSIO transmitted a packet on network network ID
Description: Trace message for outgoing x.25 packet on a dial circuit over ISDN D-channel
| DIAL.002 |
Level: C-TRACE
Short Syntax: DIAL.002 CML X31 RCV: pkt rcved nt network ID
Long Syntax: DIAL.002 CML X31 RCV received a packet on network network ID
Description: Trace message for incoming x.25 packet on a dial circuit over ISDN D-channel
| DIAL.003 |
Level: UI-ERROR
Short Syntax: DIAL.003 No cnfg nt network ID
Long Syntax: DIAL.003 No configuration found for net network ID
Description: No SR_VRTBLK record found in SR_VNET block.
Cause: Incomplete configuration
Action: Review your configuration for this network.
| DIAL.004 |
Level: UI-ERROR
Short Syntax: DIAL.004 bd dl net on nt network ID
Long Syntax: DIAL.004 Bad dial network specified in config, net network ID
Description: The base net configured is either not present, or not an ISDN BRI net.
Cause: Configuration error.
Action: Configure a valid base net.
| DIAL.005 |
Level: U-INFO
Short Syntax: DIAL.005 Caller id clid match found in Authentication list, but no ANY_INBOUND found
Long Syntax: DIAL.005 Caller Id clid match found on Authentication list but no net with ANY_INBOUND configured
Description: Checking Callerid for entries in callback table
Cause: Q931 setup received, match clid with entry in auth list, but no any inbound was available
Action: None
| DIAL.009 |
Level: UI-ERROR
Description: There is a software problem.
Cause: software error.
Action: Contact support.
| DIAL.010 |
Level: UI-ERROR
Short Syntax: DIAL.010 X.31 TEI mismatch: rcv= rcvTEI,cfg/negot= cfg_ngotTEI on nt int /
Long Syntax: DIAL.010 X.31 TEI mismatch: received tei= rcvTEI,configured or negotiated tei= cfg_ngotTEI on net interface /
Description: The dial circuit is misconfigured.
Cause: Configuration error.
Action: Review your configuration for this dial circuit.
| DIAL.011 |
Level: C-TRACE
Short Syntax: DIAL.011 CML state state_string,, event event_string, nt network ID
Long Syntax: DIAL.011 CML state state_string,, event event_string,, net network ID
Description: FSM trace event.
| DIAL.012 |
Level: UI-ERROR
Short Syntax: DIAL.012 X.31 bad TEI state: tei= rcvTEI on nt int /
Long Syntax: DIAL.012 X.31 TEI state is not multi frame for tei= rcvTEI, on net interface /
Description: The dial circuit's self test is not successful.
Cause: Network/Configuration error.
Action: Review your configuration for this dial circuit.
| DIAL.013 |
Level: U-INFO
Short Syntax: DIAL.013 Query Caller id table for clid from ISDN/ interface
Long Syntax: DIAL.013 A setup was recived with Calling Party number clid on interface interface
Description: Checking Callerid for entries in callback table
Cause: Q931 setup received
Action: None
| DIAL.014 |
Level: U-INFO
Short Syntax: DIAL.014 Found Caller id match for clid for callback on net interface
Long Syntax: DIAL.014 Caller Id matched in the table clid for dial circuit interface interface
Description: Clid match callback that destination
Cause: Q931 setup received
Action: None
| DIAL.016 |
Level: U-INFO
Short Syntax: DIAL.016 No match found Caller id clid for callback on specific net
Long Syntax: DIAL.016 Caller Id not matched in the table clid for dial circuit interface
Description: No Clid match to callback that destination
Cause: Q931 setup received
Action: None
| DIAL.017 |
Level: U-INFO
Short Syntax: DIAL.017 Caller id clid no match found in Authentication list,
Long Syntax: DIAL.017 Caller Id clid no match found on Authentication list to callback
Description: Checking Callerid for entries in callback table
Cause: Q931 setup received
Action: None
| DIAL.018 |
Level: U-INFO
Short Syntax: DIAL.018 Caller id callback on net interface
Long Syntax: DIAL.018 Caller Id callback on interface interface
Description: callback the destination
Cause: Callback Timer expired
Action: None
| DIAL.019 |
Level: U-INFO
Short Syntax: DIAL.019 Caller id callback on any_inbound net interface
Long Syntax: DIAL.019 Caller Id callback on any inbound interface interface
Description: callback the destination
Cause: Callback Timer expired
Action: None
| DIAL.020 |
Level: U-INFO
Short Syntax: DIAL.020 Caller id clid - Call blocked on net ISDN/ net
Long Syntax: DIAL.020 Caller Id clid match found on call block table for net net
Description: Checking Callerid for entries in callblock table
Cause: Q931 setup received
Action: None
| DIAL.021 |
Level: C-TRACE
Short Syntax: DIAL.021 CML state state_string,, event event_string, nt network ID
Long Syntax: DIAL.021 CML state state_string,, event event_string,, net network ID
Description: FSM trace event.
| DIAL.022 |
Level: UI_ERROR
Short Syntax: DIAL.022 LID no bf, message_type, not snt nt network ID
Long Syntax: DIAL.022 LID no buffer, message_type, msg not sent on net network ID
Description: Line ID code couldn't allocate a buffer to send a message.
| DIAL.023 |
Level: UE_ERROR
Short Syntax: DIAL.023 LID NAK rcv nt network ID
Long Syntax: DIAL.023 LID NAK received net network ID
Description: The other end of the switched circuit didn't like the LINE ID we sent, and returned a NAK.
Action: Check configuration on both sides. Remote side does not think we should be calling it.
| DIAL.024 |
Level: C-INFO
Short Syntax: DIAL.024 LID ACK rcv nt network ID
Long Syntax: DIAL.024 LID ACK received net network ID
Description: The other end of the switched circuit liked our line ID.
| DIAL.025 |
Level: UE_ERROR
Short Syntax: DIAL.025 LID tmo on mdm sgs nt network ID
Long Syntax: DIAL.025 LID timeout waiting for modem signals to come up on net network ID
Description: Either an inbound or outbound call, the V.25bis modem signals did not come up after the call was connected.
Action: Check line and modems. Line quality may be insufficient.
| DIAL.026 |
Level: UE_ERROR
Short Syntax: DIAL.026 LID tmo on id nt network ID
Long Syntax: DIAL.026 LID timeout waiting for line ID from other side, net network ID
Description: Timed out waiting for line ID from remote side.
Action: Check configuration of whoever is calling into this router. They are not sending line ID message. Might be an incompatible router.
| DIAL.027 |
Level: UE_ERROR
Short Syntax: DIAL.027 LID unkn id [ bad_lineid_string,]; nk snt, nt network ID
Long Syntax: DIAL.027 LID unknown line ID [ bad_lineid_string,] received; NAK sent, net network ID
Description: An ID message was received corresponding to a phone number from which you do not want any calls, that is, a phone number that does not exist, or the number exists but is configured for no inbound calls.
Action: Check configuration of both routers.
| DIAL.028 |
Level: UE_ERROR
Short Syntax: DIAL.028 LID no dflt circt; data ign nt network ID
Long Syntax: DIAL.028 LID no default circuit; received data was ignored, net network ID
Description: Received data from other side rather than line ID, but had no default circuit to assign the data to.
Action: Check configuration of whoever is calling into this router. They are not sending line ID message. Might be an incompatible router.
| DIAL.029 |
Level: C-INFO
Short Syntax: DIAL.029 No dl crct inc call on nt switched network ID
Long Syntax: DIAL.029 No dial circuit configured for inbound calls on switched network switched network ID
Description: An inbound call was received over the switched network, and there isn't a dial circuit configured to take it.
Cause: Misconfiguration.
Action: A dial circuit needs to be configured to accept inbound calls.
Cause: Wrong number.
Action: If this persists, you may want to pursue what avenues you can to identify a possible security break-in.
| DIAL.030 |
Level: C-TRACE
Short Syntax: DIAL.030 nt dial network ID st cml_state; cnt acpt call on nt switched network ID
Long Syntax: DIAL.030 net dial network ID is in state cml_state; can't acpt call on network switched network ID
Description: A dial circuit was found that would take the incoming call, but it is not in a state where it can do so.
| DIAL.031 |
Level: C-TRACE
Short Syntax: DIAL.031 Inbnd dsbl nt dial network ID; cnt acpt call on nt switched network ID
Long Syntax: DIAL.031 Inbound calls disabled on net dial network ID; can't acpt call on network switched network ID
Description: The network would accept a call from a specified caller, but it is configured not to accept inbound calls.
| DIAL.032 |
Level: C-TRACE
Short Syntax: DIAL.032 LID st old_state,-> new_state, nt network ID
Long Syntax: DIAL.032 Line ID state old_state, changed to new_state,, net network ID
Description: FSM trace event.
| DIAL.033 |
Level: C-TRACE
Short Syntax: DIAL.033 LID ID rcv: line_id_string nt network ID
Long Syntax: DIAL.033 Line ID received: line_id_string, net network ID
Description: A Line ID message was received containing the specified address. Note: Only the digits 0-9 are printed, since only they are significant.
| DIAL.034 |
Level: C-TRACE
Short Syntax: DIAL.034 nt dial network ID acptd call on nt switched network ID
Long Syntax: DIAL.034 net dial network ID accepted call on network switched network ID
Description: The specified network has accepted the inbound call.
| DIAL.035 |
Level: C-TRACE
Short Syntax: DIAL.035 No avl net for inbound call on nt switched network ID
Long Syntax: DIAL.035 No available net for call on network switched network ID
Description: There is no network that can take the inbound call.
| DIAL.036 |
Level: C-TRACE
Short Syntax: DIAL.036 ISDN inb Caller Id addr [ address] nt switched network ID
Long Syntax: DIAL.036 ISDN inbound address [ address] network switched network ID
Description: The router passed the specified address and subaddress of the caller in an ISDN setup message.
| DIAL.037 |
Level: C-TRACE
Short Syntax: DIAL.037 LID ID snt: line_id_string nt network ID
Long Syntax: DIAL.037 Line ID sent: line_id_string, net network ID
Description: We sent the specified line ID message to the destination.
| DIAL.038 |
Level: C-INFO
Short Syntax: DIAL.038 Too many circuits nt base network ID
Long Syntax: DIAL.038 Too many circuits on net base network ID
Description: There are more virtual circuits that are active than the interface type supports.
| DIAL.039 |
Level: C-INFO
Short Syntax: DIAL.039 Higher pri conn nt preempted network ID preempts nt higher-priority network ID
Long Syntax: DIAL.039 Higher priority connection request for net preempted network ID preempts net higher-priority network ID
Description: A connection request for a higher-priority dial circuit caused the specified lower-priority circuit to terminate.
| DIAL.040 |
Level: C-INFO
Short Syntax: DIAL.040 Disc ind on pri conn nt network ID; retry
Long Syntax: DIAL.040 Disconnect indication received for priority connection network network ID; retry
Description: The router received a disconnect indication for the specified network, but the base network did not actually attempt the connection. The router rejected the connection because the base network was not ready. The router will retry the connection shortly.
| DIAL.041 |
Level: C-INFO
Short Syntax: DIAL.041 outbound call denied, configed inbound nt network ID
Long Syntax: DIAL.041 Outbound calls denied network network ID
Description: Router would like to place outbound call, but configuration prevents it.
| DIAL.042 |
Level: C-INFO
Short Syntax: DIAL.042 idle exp nt network ID
Long Syntax: DIAL.042 idle timer expired and call cleared, net network ID
Description: The idle timer of a demand-based net expired, and the call was cleared.
| DIAL.043 |
Level: C-TRACE
Short Syntax: DIAL.043 Match dial addr [ dial_address] to nt switched network ID
Long Syntax: DIAL.043 Matched inbound destination dial address [ dial_address] to network switched network ID
Description: An inbound call arrived and the specified network is configured to match it. Match the dial_address address string in hex. Empty string is a wildcard and will match a network with any_inbound setting.
| DIAL.044 |
Level: C-TRACE
Short Syntax: DIAL.044 No usbl match dial addr [ dial_address]
Long Syntax: DIAL.044 No useable match dial addr [ dial_address]
Description: No more dial circuits match inbound address.
| DIAL.045 |
Level: C-TRACE
Short Syntax: DIAL.045 Dialing dest < dest_name>, DTE number [ dte_addr], nt network ID
Long Syntax: DIAL.045 Dialing destination < dest_name>, DTE number [ dte_addr], net network ID
Description: The Connection Management Library (CML) is dialing the specified destination end point using the specified DTE number. This message occurs for every DTE number the CML actually dials.
| DIAL.046 |
Level: C-TRACE
Short Syntax: DIAL.046 CMLB net # net_num, dest < dest>, indest < in_dest>, net network ID
Long Syntax: DIAL.046 CMLB dump: net # net_num, dest < dest>, indest < in_dest>, net network ID
Description: Traces the contents of the Connection Management Library control Block (CMLB) chain as an inbound connection vector to the correct CMLB.
| DIAL.047 |
Level: C-TRACE
Short Syntax: DIAL.047 Source DTE addr # index: [ addr_str]
Long Syntax: DIAL.047 Source DTE address # index: [ addr_str]
Description: The router called once for each DTE address string found in a CMLB's src_addrs.
| DIAL.048 |
Level: UI-ERROR
Short Syntax: DIAL.048 Bad MP config nt network ID
Long Syntax: DIAL.048 Bad MP config for net network ID
Description: The MP net configured is invalid or BRS is on the link.
Cause: Configuration error.
Action: Configure a valid MP net or turn off BRS on the link.
| DIAL.049 |
Level: UI-ERROR
Short Syntax: DIAL.049 Invalid destination addr on nt network ID
Long Syntax: DIAL.049 Bad dialer destination name specified in config, net network ID
Description: The specified destination name was not added with the "add address" command.
Cause: Configuration error.
Action: Configure a destination name using the "add address" command.
| DIAL.050 |
Level: UI-ERROR
Short Syntax: DIAL.050 Swcthd net ( switched network ID) rjctd rgstrtn for nt network ID
Long Syntax: DIAL.050 The switched network (network switched network ID) rejected the registration request for this dial circuit: net network ID
Description: The dial circuit is misconfigured.
Cause: Configuration error.
Action: Review your configuration for this dial circuit.